IUW-RVN68 Posted September 20, 2003 Report Share Posted September 20, 2003 I HAVE A AMERICAN HISTORICAL SOCIETY WEST HURLEY AO U.S. NAVY COMMEMORATIVE THOMPSON USN#25. AFTER RECENTY FIRING THIS WEAPON I DISASSEMBLED THE GROUPS TO CLEAN IT. THE BARREL WAS LOOSE AND CAME OUT WITH JUST MINOR TWIST.(IN FACT IT WAS APPARENTLY LOOSE AT RANGE,BUT I THOUGHT IT WAS THE COMPENSATOR. THE BARREL AND RECIEVER HAVE NO STAMPS OR WITNESS MARKS THAT I CAN SEE. IT APPEARS TO HAVE 35 FINS NOT INCLUDING THE END FLANGE (RECIEVER END). HOW DO I PROPERLY REASSEMBLE THE BARREL TO MAKE SURE IT IS ALIGNED? I BOUGHT SOME BLUE LOCKTITE AND A SEARS STRAP WRENCH TO DO THIS. I DID NOT SEE ANY SHIMS. CAN YOU ADVISE ON REASSEMBLY? ALSO, I AM NOT SURE ON HOW TO TAKE DOWN THE RECIEVER GROUP..NO SPECIAL TOOLS FOR RECOIL SPRINGS ETC,HELP HERE WOULD BE GREAT. Link to comment Share on other sites More sharing options...
must Posted September 20, 2003 Report Share Posted September 20, 2003 I had the same problem with my WHM1 (the barrel was loose). I sent the gun to PK in Colorado to repair (there was alot of other problems to like too long of a bolt that was damaging the chamber). It was a WH bolt. When he got through with it, it runs like a charm. http://www.machinegunbooks.com/forums/invboard1_1_2/upload/html/emoticons/smile.gif http://www.machinegunbooks.com/forums/invboard1_1_2/upload/html/emoticons/smile.gif Link to comment Share on other sites More sharing options...
PK. Posted September 21, 2003 Report Share Posted September 21, 2003 Special tools and experience are required to properly install a barrel to prevent future disappointments. This job is not expensive in itself and is better left to a professional. Link to comment Share on other sites More sharing options...
Norm Posted September 21, 2003 Report Share Posted September 21, 2003 The barrel has to be torqued on. PK is right, without the proper tools it will come loose again, or you can (and probably will) destroy the finish on the gun. http://www.machinegunbooks.com/forums/invboard1_1_2/upload/html/emoticons/sad.gif Send it to PK, and he will put on to stay. Norm Link to comment Share on other sites More sharing options...
JimFromFL Posted September 22, 2003 Report Share Posted September 22, 2003 If you ensure the thread are clean and dry, the locktitle will work fine. Link to comment Share on other sites More sharing options...
PK. Posted September 22, 2003 Report Share Posted September 22, 2003 Phil, I appreciate the comments. If a barrel is properly installed, it should never “self tighten” and will stay aligned forever. There are many variables to be considered when installing a barrel on a Thompson. A few of these include the stud on the grip mount, the surface of the receiver nose, depth of the hole and the flange on the barrel, the length of the barrel shank and the condition of the threads, burrs on everything not to mention the headspace and chamber dimensions. I know that it looks like a simple job; unscrew old barrel and screw on new one- but it ain’t the case most of the time. The wall of finned Thompson barrels is actually quite thin (.098) and these can be crushed or twisted fairly easily if the right tool and techniques aren’t applied. None of this is to imply that I’m the only guy who can change out a Thompson barrel; ‘taint so. But, it is not for everyone. If you are going to attempt it, please do your homework and make sure you know what you are doing; it is more complicated that it would appear. All in all, it’s cheaper to allow an experienced gunsmith who has the tools to do the job right, the first time. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now