Dborns Posted December 3, 2016 Report Share Posted December 3, 2016 The two original mags I have are really hard to get into the magwell, and even harder to get out. I degreased, cleaned, and put a little oil on them but that didn't help. Neither the mags or magwell look to be damaged or out of square. I was thinking about sanding the tops of the mags down a little, but don't know if that'll help either. To get them out, I have to brace the rifle between my legs and wiggle the mag while pulling hard on it. Theyre that tight.Any suggestions? Link to comment Share on other sites More sharing options...
StooperZero Posted December 3, 2016 Report Share Posted December 3, 2016 I had a few that were like that in the MKIII's . any markings on the mags? i could dig them up and test fit cause it was always from the same maker. Link to comment Share on other sites More sharing options...
1gewehr Posted December 3, 2016 Report Share Posted December 3, 2016 Take a mag without much finish on it and cover the top with a black magic marker. Insert and remove from magwell. The scratches will show where it is binding.I'd guess that you have a out-of-square magwell. Gentle work in a bench vise can fix that. Link to comment Share on other sites More sharing options...
Dborns Posted December 4, 2016 Author Report Share Posted December 4, 2016 The mags are scrapped up a bit, but I couldn't tell if that was from old wear. I'll try the marker and see what that shows. Thanks for the help. Link to comment Share on other sites More sharing options...
Dborns Posted December 4, 2016 Author Report Share Posted December 4, 2016 The mags are scrapped up a bit, but I couldn't tell if that was from old wear. I'll try the marker and see what that shows. Thanks for the help. Link to comment Share on other sites More sharing options...
MG08 Posted December 8, 2016 Report Share Posted December 8, 2016 you might want to try some other Mags, since the variety of magazines and guns made over the years may not always be "made for each other". I have had a LOT of STENS and sten mags over the years ( Last time I bought some I got 100 mags) and one country made guns and mags but they may not fit another countries that well. They do not all fit equally well. I would try different mags before I started cutting grinding welding to fit - Link to comment Share on other sites More sharing options...
Dborns Posted December 8, 2016 Author Report Share Posted December 8, 2016 I used a marker on both mags and they were dragging on the sides on both. I took a sanding wheel and took a little metal off until the both were looser. They aren't drop free by any means, but at least I can pull them out easier. All the metal work is done, I just have the receiver tack welded to the lower for now. I want to wait to finish securing it permanently until I get the bolt. IO is still showing backorderd on them, so I'll have to keep checking with them. Its too bad the receiver tube is new. I'd like to keep the original color of the rifle, but the upper needs to be painted. I'm going to look for some paint that is close to the original paint. Link to comment Share on other sites More sharing options...
m3bobby Posted December 9, 2016 Report Share Posted December 9, 2016 Sten mags are never tight unless something is wrong. Are you sure they are Sten mags? Before you adjust anything more, wait until you have your bolt and can test them for functionality. You may find they don't feed very well anyway. It was normal to retain compatible mags with a specific gun when they were known to work well. I have a Sten Mk1, a LB Mk2, 3 Faz Mk2, a Lined Bros Mk3 and a Thrace Mk5 and the LB Mk2 has the best fitting Mag to Mag housing of any of them, those Canadians knew how to make a quality cheap product! Link to comment Share on other sites More sharing options...
2ndArmored Posted December 26, 2016 Report Share Posted December 26, 2016 Regarding paint, you can try: http://www.desertfoxsales.com/BRITISH_BLACK_GUN_SPRAY_PAINT_p/dfs-344.htm You can try them too: http://www.milsurps.com/images/imported/2012/10/BritishBlack2-1.jpg I can't vouch for either product because I had some of this already sitting in my garage and it worked well: http://www.homedepot.com/catalog/productImages/600/a1/a18bd6cc-f11b-46e7-8895-a8bfecacac9d_600.jpg Strip all the old finish off and then apply it in light coats to a uniform surface. Patience, young Jedi.... (Better prep always yields better results.) It's durable and matches the finish on my buttstock well. (I respect the history of these guns, but mine had been so re-painted so many times that I didn't see my efforts as diminishing the authenticity any.) Regarding the mags, they are the weak link in the weapons system. After the war, many French partisans commented that Sten guns were easy to get - reliable mags were not. In fact they'd pocket them during a firefight because they didn't have the luxury of getting more later. But once you get a combo that works, tis a glorious thing. :woot: Link to comment Share on other sites More sharing options...
Dborns Posted December 28, 2016 Author Report Share Posted December 28, 2016 (edited) Thanks for the links, I may try the British Black paint. I saw some Krylon green camo that I might try also, since mine is already an off green color. I'm guessing that's the original paint? I've got the bolt in and the mags are coming out easier, so I'm ready to shoot as soon as I can get to the range. The only other issue I saw was when I used dummy bullets to test chambering and ejection, they are tipped up a little bit in the mags. But again, that's with lighter dummy bullets and only a couple loaded at a time. Edited December 28, 2016 by Dborns Link to comment Share on other sites More sharing options...
2ndArmored Posted December 29, 2016 Report Share Posted December 29, 2016 I've never seen a green sten - just black (either painted or 'blued'). Kinda like Mr. Ford's color options on the Model T. The feed angle should be 7.5 degrees, +/- 0.5 deg. Your actual mileage may vary, depending on the the spacing & condition of the feed lips acting on the brass. (You may also want to invest in one of these: http://www.brpguns.com/products/STEN-Magazine-Repair-Tool-Set.html ) Quantity & composition of the ammo shouldn't change that. But live fire is always mysteriously different from cycling ammo by hand. Things move a lot faster & harder (and hotter). Anticipated problems disappear as often as unexpected difficulties pop out of nowhere. Keep in mind that you're making a gun, something that Mssrs. Thompson, Browning, et al. could tell you is a complicated lengthy process of trial & error. Link to comment Share on other sites More sharing options...
m3bobby Posted December 29, 2016 Report Share Posted December 29, 2016 There was an EMER that said green paint could be used in a jungle climate but I've never seen evidence that it was ever used. Either the STEN didn't need it as it was simple to keep clean or they ended up so rotten they were scrapped. Link to comment Share on other sites More sharing options...
Dborns Posted December 29, 2016 Author Report Share Posted December 29, 2016 I'll take both mags with me to test feeding on them both. As far as the paint, I can't get a good pic of the color, but mine is definitely not black, so it's been repainted at some point. It's a dark olive green color. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now