Grease Gunner Posted October 1, 2018 Report Share Posted October 1, 2018 Hello Fellow Board Members:I have a 1927a5 that would be a great SBR conversion to accept a 1928 buttstock.I have all the licenses necessary-Have 07 MFR with SOT stamp. I am not aware where the adapter plates or kits can be found Your help is appreciated or if you have one to sell let me know I have an older WH pistol not the cuurent crop of TA5 Thanks Haris Link to comment Share on other sites More sharing options...
peter kohler Posted October 2, 2018 Report Share Posted October 2, 2018 my machine shop made my plate for me. he used a wider piece of flat bar and milled it down. he also did the lower frame. after a bit of minor filing it slid right in with no side to side wiggle. my stock and all my hardware came from a garage sale. I just lucked out one day and found a bunch of Thompson stuff so I bought it all. sarco has the stock, stock latching plate and screws. theres another vendor that's called keystone that has the correct latch spring. the adapter plate is the same size as the inside of the latch plate. theres a diagram on this site that give the dimensions for the machine work on your lower. ive tried posting pictures of mine but just cant seem to figure it out I need some help there Link to comment Share on other sites More sharing options...
Grease Gunner Posted October 7, 2018 Author Report Share Posted October 7, 2018 (edited) I have an extra 1928 stock with all the metal and the latching plateso that can be adapted where can i get this adapter plate? ThanksIf you find the diagram, please send me a link to it Edited October 7, 2018 by Grease Gunner Link to comment Share on other sites More sharing options...
95mustang Posted October 8, 2018 Report Share Posted October 8, 2018 Its just a PC of flat bar 1/8 inch thick.It is 4 inches long by the width of the latch plate slot (as Pete says, machine the width to match the latch plate minus a few thousand and it will be rattle free)Now on your trigger frame , you are going to have to have it machined on a mill.to match the profile of a 28Then you drill and tap receiver/Trigger frame so you can bolt the plate on .M4 flat heads work extremely well Link to comment Share on other sites More sharing options...
Grease Gunner Posted October 8, 2018 Author Report Share Posted October 8, 2018 95mustang.........Thanks a lot!! Link to comment Share on other sites More sharing options...
Paladin601 Posted October 9, 2018 Report Share Posted October 9, 2018 careful, if you live in a Gun Control state, you can make a legal gun illegal. Just a Public service announcement Link to comment Share on other sites More sharing options...
Grease Gunner Posted October 11, 2018 Author Report Share Posted October 11, 2018 i will register it on a form 2 as I am a 07/02 careful, if you live in a Gun Control state, you can make a legal gun illegal. Just a Public service announcementi will register it on a form 2 as I am a 07/02 Link to comment Share on other sites More sharing options...
choppero Posted October 22, 2018 Report Share Posted October 22, 2018 Coming real soon, screw on adapter that looks like the original. My website is lcgnm.com. I used to make them under the name chopper ordnance along with new stock slides that fit like the original. But unless I had a real incentive to make those thare are just too many steps in the process to be worth while. Link to comment Share on other sites More sharing options...
Grease Gunner Posted October 22, 2018 Author Report Share Posted October 22, 2018 choppero:Are you saying you will ro wont make them? Link to comment Share on other sites More sharing options...
choppero Posted October 23, 2018 Report Share Posted October 23, 2018 Yes. I think you asked will I make them. I am tooling up today. I have the material and will have some ready probably tomorrow if all goes as planned. My credit card merchant account should be read t to tale orders by then I hope. Link to comment Share on other sites More sharing options...
Grease Gunner Posted October 24, 2018 Author Report Share Posted October 24, 2018 I will buy one!! Link to comment Share on other sites More sharing options...
choppero Posted October 24, 2018 Report Share Posted October 24, 2018 I am still waiting for my merchant credit card bank to finalize my on line store. If you PM me I can give you my email Link to comment Share on other sites More sharing options...
Paladin601 Posted October 24, 2018 Report Share Posted October 24, 2018 How much? Link to comment Share on other sites More sharing options...
choppero Posted October 30, 2018 Report Share Posted October 30, 2018 Go to https://shop.lcgnm.com they are listed under Auto Ordnance Thompson Parts and Accessories. I'm supposed to have the credit card autorization today. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now