Rat-a-Tat Posted April 9, 2019 Report Share Posted April 9, 2019 Severely torched upper and lower, welded. Someone one did this long ago it appears. Had somerust, pitting, etc. I started to clean it up but needs more help than I can give it.Trying to figure out which methods best to finish it.Thinking of sandblast and maybe durafil and/or duracoat flat finish to try to minimize the numerous imperfections.Maybe leads to someone that does this sort of thing and has knowledge of Thompsons. Appreciate any thoughts/suggestions.My wife though it would make a nice anchor for my fishing boat and numerous other real great ideas! Link to comment Share on other sites More sharing options...
Black River Militaria CII Posted April 9, 2019 Report Share Posted April 9, 2019 Use the value of duracoat as a mask for fill-and-finish welding of the various metal surface issues. If makes no sense to expect any paint to “fill” and eliminate rough, pitted, degraded areas especially on flat surfaces. Paint will accentuate the cery textures you are trying to eliminate. The problem areas can be weld filled and the surfaces retrued to flat, and if this is done carefully and well, then duracoat will make the metal surfaces look really good. As you realize, the gun will never be more than a shooter, but it can look good nontheless. Kudos to you for wanting to make restore it.I have been repairing semi-MG42s that were poorly constructed and some have been welded togther with stainless welding rod. The owners want parkerized or blued finish but the stainless will not take these finishes without special treatment and then lften not well. The labor to remove the stainless weld and replace with mild steel is prohibitive so duracoat has been very effective in putting an acdeptable finish on these guns. Same for other MGs I have built that have vintage parts that will not blue but turn redish in color despite alternate methods of bluing employed. Duracoat has veen extremely useful in these cases. Plus it it is a very tough finish and won’t oxidize. FWIW Link to comment Share on other sites More sharing options...
Rat-a-Tat Posted April 10, 2019 Author Report Share Posted April 10, 2019 Thanks for the reply. This isn't a shooter. The upper and lower are welded together as is the barrel and even the magazine,Not expecting to be able to hide where it was torched completely. Just make it as good as possible and hang some new/aged furniture on it.A SBR shooter isn't gonna happen for me so I would be happy with a SMG display piece and hang it with my real Garand, M1 Carbine & 03 Springfield.Then it would complete my bucket list having the rifles I used in the service.I got to figure out how to post a pic or two that may help. Link to comment Share on other sites More sharing options...
Rat-a-Tat Posted April 10, 2019 Author Report Share Posted April 10, 2019 http://i.imgur.com/DhiMlKxm.jpghttp://i.imgur.com/Bp2gFt0m.jpg Link to comment Share on other sites More sharing options...
Black River Militaria CII Posted April 10, 2019 Report Share Posted April 10, 2019 (edited) Oh, well, having repaired some registered live MGs that look like that gun I assumed it was a registered example.Good luck. Edited April 10, 2019 by Black River Militaria CII Link to comment Share on other sites More sharing options...
Rat-a-Tat Posted April 10, 2019 Author Report Share Posted April 10, 2019 Nothing live on this, its welded everywhere and was torched in two places thru the upper and lower receiver and appears to of had the frontbroken or cut off, so the receiver was in four pieces not counting the lower.My understanding is that this is legal to possess and not considered a firearm, am I wrong? Link to comment Share on other sites More sharing options...
Haenelistklasse Posted April 10, 2019 Report Share Posted April 10, 2019 Uhhh, well, I am certainly no expert but it appears like it was welded back together by someone making it an unregistered MG. If it were me, I would get rid of it. Maybe someone else can chime in that knows a bunch more than me. Take care, Haenelistklasse Link to comment Share on other sites More sharing options...
Rat-a-Tat Posted April 10, 2019 Author Report Share Posted April 10, 2019 Well I never expected that as it's unfireable and locked up therefore not functional as a machine gun.Hell I was just looking for some leads for someone to fill in some pitting and paint the damn thing!But if for whatever the reason is illegal I would certainly like to know that.Ya mean the wife was right its only good for a boat anchor, damn i'm never gonna tell her she was right! Link to comment Share on other sites More sharing options...
Haenelistklasse Posted April 10, 2019 Report Share Posted April 10, 2019 Well, I understand what you are saying about being locked up but if the receiver is welded back together then I would say it is a MG again even if you can't get it to fire. Maybe someone else will come along that knows more than me. Good luck, Haenelistklasse Link to comment Share on other sites More sharing options...
Rat-a-Tat Posted April 11, 2019 Author Report Share Posted April 11, 2019 Okay I think a grayed duracoat similar to Parkerizing would look right.And I can’t remember if the mags are a gloss black or matte. But not wanting tohightlight the imperfections a matte black would probably work nice.Still looking for some places or individuals that perform duracoating which seemsThe best way to go. And preferably familiar with Thompson’s. Appreciate any leads.Thanks for the responses thus far. Link to comment Share on other sites More sharing options...
Broadarrowmaint Posted April 11, 2019 Report Share Posted April 11, 2019 Get it bead blasted and then hot blue it for a dulite type finish. Ive done that to my semi Kahr 28 and an 80% reciever and it turns out great! Link to comment Share on other sites More sharing options...
Black River Militaria CII Posted April 11, 2019 Report Share Posted April 11, 2019 I assume the breech is welded shut, right? Barrel welded to receiver, right? What’s the state of the inside of the receiver? Looks like the upper and lower are welded together so look inside through the cocking slot and see what it iis like inside? Bolt in it or no bolt? If bolt is in the receiver, can it go back and forth? If the bolt can. Move vack and forth time to have it welded in place. There is a degree of destruction to an MG receiver that goes beyond torching it into four parts. There are quite a few “dummy” MGs out there with complete receivers but the extent of the welded damge is sufficient for the gun to be a non- gun. If you are in doubt, you can always have a shop further weld the upper to the lower, bolt to the receiver, etc, etc. Have fun...... Link to comment Share on other sites More sharing options...
Rat-a-Tat Posted April 11, 2019 Author Report Share Posted April 11, 2019 it's a non-gun. No Doubts! Link to comment Share on other sites More sharing options...
Rat-a-Tat Posted April 11, 2019 Author Report Share Posted April 11, 2019 There's alot of places that do nice gun refinishing work. Would prefer to find someone with some base knowledge of Thompsons and the patience to work on this. Any leads would be greatly appreciated. Thank You. Link to comment Share on other sites More sharing options...
Broadarrowmaint Posted April 11, 2019 Report Share Posted April 11, 2019 Look up Ravenna armory. He does refinishing and would be happy to refinish your Thompson to a correct wartime finish. Hes a great guy, and does terrific work and he could make that Tommy look great! Link to comment Share on other sites More sharing options...
Broadarrowmaint Posted April 11, 2019 Report Share Posted April 11, 2019 https://www.ravennaarmory.com Link to comment Share on other sites More sharing options...
Rat-a-Tat Posted April 12, 2019 Author Report Share Posted April 12, 2019 Thank you for the lead Broadarrowmaint., much appreciated! Link to comment Share on other sites More sharing options...
Rat-a-Tat Posted December 23, 2019 Author Report Share Posted December 23, 2019 (edited) And here we are today: Edited December 29, 2019 by Rat-a-Tat Link to comment Share on other sites More sharing options...
reconbob Posted December 24, 2019 Report Share Posted December 24, 2019 I know it makes no sense but my understanding is that if a receiver is welded back togetherthe ATF gives themselves the option to consider it a firearm, regardless of any extra welding thatmay have been done to prevent it from working. IMA sells dummy/display machine guns fabricated from original machine guns but they go tothe trouble of cutting out 3/4" of the gun then welding everything back together. If all they had to dowas weld everything shut they certainly would not go to the extra trouble to do this. I would not lose any sleep over this but I would also not take it to a gun show.... Bob Link to comment Share on other sites More sharing options...
Rat-a-Tat Posted December 24, 2019 Author Report Share Posted December 24, 2019 Thanks Bob, comparing it to the high quality of IMA’s work is a complement indeed.Actually if you read MY descriptions above starting with “Severely torched upper and lower”you would understand why it would be classed non-gun.I'm pleased with it considering the mess it was and have it proudly displayed with my WW2 Garand, M1 Carbine & 03 Springfield. Have a Merry Christmas one and all!!! Link to comment Share on other sites More sharing options...
MG08 Posted December 25, 2019 Report Share Posted December 25, 2019 I would heed what Bob said though - We had a local case here in MN where a guy who could not own a gun ( no reason given in the news) was arrested and charged with possession of illegal MGs for taking parts kits and welding them together enough to hang on the wall. Federal court in Mpls,, he was convicted of MG possession. The guns were not "rebuilt" in any fashion, just tack welded to hold them together. I actually saw him and one of the Thompsons at a Gun show in St Cloud MN, and to say the gun was dewatted was an understatement. Welded inside, bolt welded in place, barrel welded, HOLES in the torch cut receiver where he did not weld it up. He is doing however many years they gave him in a medium security prison here. It can be fairly arbitrary from the BATF standpoint as far as who they charge and what the press for cases. Sadly - it can be more about conviction statistics than fair and just treatment. Link to comment Share on other sites More sharing options...
Rat-a-Tat Posted December 25, 2019 Author Report Share Posted December 25, 2019 (edited) convicted felon? yea I guess he could't pissed the authorities and they understandably went thru him.I often wondered about all those numerous cut receivers and parts kits for sale on gunbroker, armslist and even seen them on ebay?What gives with BATF on those? NFA answer to that question;Are parts or kits which would convert a firearm into a machinegun subject to registration?Yes.So its probley a mater of interpretation, would it be used to convert/manufacture a SMG or perhaps the parts kit doesn't contain the critical parts and the receiver meets legal cutting/torching requirments so NFA & BATF gives them a pass with bigger fish to fry. Edited December 26, 2019 by Rat-a-Tat Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now