
Source For Xx Mags?
Started by
mgdoc8307
, May 04 2004 06:24 PM
12 replies to this topic
#1
Posted 04 May 2004 - 06:24 PM
Looking to buy four XX mags for presentation in "police case". Any suggestions ? Thanks, Michael
#2
Posted 04 May 2004 - 07:43 PM
Are you looking for near mint mags or any condition?
#3
Posted 05 May 2004 - 07:16 AM
I'd like to find some, too.
#4
Posted 05 May 2004 - 08:46 AM
WhataCountry has used XX mags.
#5
Posted 05 May 2004 - 10:19 AM
Don't expect What a Countrys mags to look good. Just received 5 more. Most are shooters only. Pitted, bent and wouldnt feed until I used the anvil on lips.
Two weeks ago there was a dated mag in excellent condition on Ebay - it sold for over $200. - ONE mag!
Two weeks ago there was a dated mag in excellent condition on Ebay - it sold for over $200. - ONE mag!
#6
Posted 05 May 2004 - 06:37 PM
Where would one find this anvil & how is it used?
#7
Posted 05 May 2004 - 07:01 PM
QUOTE (Ron A @ May 5 2004, 10:19 AM) |
Don't expect What a Countrys mags to look good. Just received 5 more. Most are shooters only. Pitted, bent and wouldnt feed until I used the anvil on lips. Two weeks ago there was a dated mag in excellent condition on Ebay - it sold for over $200. - ONE mag! |
How were they able to have the auction last that long?
If its the one I am thinking then they must have stated it held 10 rounds.
#8
Posted 05 May 2004 - 07:11 PM
Jim from Fl - to answer your question:
The mag sold for $207.25 item #2239462272 - the auction started on 4/18 and went until 4/25. The seller didn't say how many rounds the mag held, just showed photos of the mag. He had 18 bids.
The mag sold for $207.25 item #2239462272 - the auction started on 4/18 and went until 4/25. The seller didn't say how many rounds the mag held, just showed photos of the mag. He had 18 bids.
#9
Posted 05 May 2004 - 07:16 PM
Ahhhhh, it is listed as a Thompson "Part" not Mag.
I may give it a try with my mags... oh, i mean "parts".
I may give it a try with my mags... oh, i mean "parts".
#10
Posted 05 May 2004 - 07:46 PM
You could always take the mags, and make into parts and sell as parts.
#11
Posted 05 May 2004 - 08:03 PM
Saw 2 dated XX at a gun show, didn't buy them, they were asking 100 each. From what I saw they looked refinished..
I wish I would have gotten their business card or something, but the parts they had were high by all standards.
$18 for an extractor to me is high no matter where it came from.
I wish I would have gotten their business card or something, but the parts they had were high by all standards.
$18 for an extractor to me is high no matter where it came from.
#12
Posted 06 May 2004 - 05:12 PM
QUOTE (LSU Tiger @ May 5 2004, 06:37 PM) |
Where would one find this anvil & how is it used? |
ditto, except for the how to use part

#13
Posted 07 May 2004 - 12:23 PM
Glenn Whittenberger is the one who has been selling the mag anvils. As I recall, he gets $50 for one. He did a post recently for the M1/28 recoil springs he is selling, so I suggest you contact him about the anvils.
Roger
Roger