How many audible clicks do you wind your Kahr made L drums?
MadDog
How Many "audible" Clicks To Wind A Kahr L Drum?
Started by
MadDogDan
, Aug 18 2005 11:34 AM
5 replies to this topic
#1
MadDogDan
-
- Regular Group
-
- 32 posts
Member
Posted 18 August 2005 - 11:34 AM
My Kahr L Drum has two different click sounds that are hard to differentiate between each other. If you wind the drum key the 9 to 11 clicks that it says to, the drum doesn't work properly. I just spoke with Kahr and they told me that you count four audible clicks as "One True Click". If this is true why in the hell don't they say that in the instructions that come with the damn thing????
How many audible clicks do you wind your Kahr made L drums?
MadDog
How many audible clicks do you wind your Kahr made L drums?
MadDog
#2
Norm
-
- Board Benefactor
-
- 2514 posts
Long Time RKI Member
- Gender:Male
- Location:Memphis, TN
- Interests:Thompsons (of course), Electronics, Physics, History, Mechanics, Collecting License Plates.
Posted 18 August 2005 - 11:39 AM
Ignore the little "clicks." It is the loud "CLUNKS!" that you count.
Also, I think that one click (that counts) is 1/4 of a turn.
Norm
Also, I think that one click (that counts) is 1/4 of a turn.
Norm
#3
giantpanda4
-
- Board Benefactor
-
- 2413 posts
Respected Member
- Gender:Male
- Location:Howell, MI 48855
- Interests:Mechanical toys - cars, instruments, and of course - guns. The 1921-28 thompsons are the epitomy of perfection for a mechanical device that fills all my interests!
Posted 18 August 2005 - 11:43 AM
Mad Dog is right - 1/4 turn + 1 click, so go about 2 and a quarter turns
#4
timkel
-
- Board Benefactor
-
- 1393 posts
Long Time RKI Member
- Gender:Male
- Location:USA
-
Interests:NRA Patron member
Atlas Shrugged
Posted 18 August 2005 - 02:06 PM
Its a fairly easy job to fix the click problem.
-Remove the rotor
-examine the rivet heads on the inside back of the drum
-set the 4 rivets again to flatten them down
-then grind down the rivet heads some more
-assemble the drum and test the drum clicks
-when satisfied, reblue the rivet heads
Done!
-Remove the rotor
-examine the rivet heads on the inside back of the drum
-set the 4 rivets again to flatten them down
-then grind down the rivet heads some more
-assemble the drum and test the drum clicks
-when satisfied, reblue the rivet heads
Done!
#5
Lotusnut
-
- Regular Group
-
- 59 posts
Member
Posted 18 August 2005 - 03:10 PM
as many as you like...won't work anyway....
#6
Grey Crow
-
- Board Donor
-
- 1077 posts
RKI Member
- Location:North Central Pennsylvania
- Interests:Thompson Submachine guns, computers, reptiles.
Posted 18 August 2005 - 10:00 PM
Before doing anything check that the cartridges slide freely through the guide rails inside.
4 clicks = 1 turn so you will need 36 clicks for 9 complete turns.
My Kahr L works great! (in a semi)
PK stated in a very early post that in adjusted drums they worked good in the 28, and were slow in the 21.
He also stated that he thought they might work in the 21 once they were run a while.
4 clicks = 1 turn so you will need 36 clicks for 9 complete turns.
My Kahr L works great! (in a semi)
PK stated in a very early post that in adjusted drums they worked good in the 28, and were slow in the 21.
He also stated that he thought they might work in the 21 once they were run a while.
