Jump to content

My 28's Sick.


Recommended Posts

Hi everybody,

I got a WH 28 that just started giving me problems. It

won't fire one or two shot burst or single shot in semi,

it wants to run the full clip. It may fire two shots then

next pull the whole clip. I have not had this problem

before it just started it one day out at the gravel pit.

I fired one 3o Rd clip at two to three shot burst just

fine then the next 30 Rd clip it started, I shot a burst

then it ran the clip and been that way since.

I have tried different ammo, recoil springs, cleaning

everything, clips, holding my mouth a different way and

it still does it.

Can any body help me, please. I am about ready to

use it to stick some Tomato plants with it.

http://www.machinegunbooks.com/forums/invboard1_1_2/upload/html/emoticons/unsure.gif BA

Link to comment
Share on other sites

Thanks all

 

I have replaced all the springs in the lower along

with a new rocker, for the semi action, but still

full auto till clip runs out. Its great for just dumping

clips but will not burst groups or shoot semi more

than twice. its like the bolt ain't comming back far

enough for the sear to catch. I have had this gun

since 1984 and I havent had any trouble till now.

I am a machinist by trade and understand the

workings of this model, but this don't add up.

I though maybe my ammo wasint hot enough,

I had some of my reloads, so I tried a box of

miltary ball and still same song.

I took the lower back down and check for burrs

or anything out of the orinary and double clean

and lube all, didn't see anythingout of place. Went

outside with 10 Rd in clip and tried again. The first

pull it shot twice then the secound pull it dumped the

clip with out my finger on the trigger.

You'all got me.

BA

Link to comment
Share on other sites

I am an admitted newbie with Thompsons but been around this stuff for 30 years. If as stated his sear/disconnector looks good could the surface of the bolt that contacts them be worn in some manner which results in these runaways?? JUst seems if he has been rocking along for many years the spring would not have gotten stronger and he has swapped aobut with good ball ammo it seems something has degraded to make this condition exist-Probably worng but that is how we learn.

 

Mark

Link to comment
Share on other sites

That is my next guess is to try a new bolt. The old

one looks ok, just shinny where the sear has been

engageing it. Can't tell it it is whorn or not, don't have

a new one yet to compare.

I have fired this weapon on and off for the past

20 years and probabley ran 7000 to 8000 Rds

through it so the bolt could posibly be shot. I will

pick up a new one and try it. I got to get my

Tommy Gun well again, I enjoy shooting it too much.

I own four other Machine Guns but the Thompson

is my favorite.

Thank to all for the help

BA

Link to comment
Share on other sites

A lot of great advice.

 

Here is some more info to muddy the waters.

 

Is the ammo the same as before?

Is the bolt being slowed down by either the mag, dirty ramp or barrel opening where the bullet sits?

 

I have experienced problems that were attributed to the above.

 

Good luck and let us know the results.

Link to comment
Share on other sites

Hey Jim

I have tryed different ammo from hand loads, factory to

miltary ball and all result same. I have tryed different

clips from 30 rd, 20 rd and even a drum with same

result. But what do you mean where bullet goes in

barrel? I clean barrel out and looked with light and

don't see anything. Is there something with the

barrel I don't know or looking over. This condistion

just started like you filp a switch. I shot a 30 rd clip

at 2-3 shot burst and it shot fine, then the very

next clip it started the run away problem. I tryed

that first clip again and still run away.

Did something happen to the throat of the barrel

or maybe the chamber that I can't see?

BA

Link to comment
Share on other sites

Simple question - does the bolt stay back after the last shot?

If not, the bolt isn't coming back far enough. Mainspring probably - or loads (as mentioned).

If so, sear/trip/bolt should be OK.

Link to comment
Share on other sites

I am not an expert, but I seem to remember and old post which someone (fullauto 45, I think) mentioned that you could put a piece of scotch tape where the acuator handle is SUPPOSED stop (across the top of the receiver.)

 

After firing, look at the tape. If it is broken, the acuator went full travel. If not, it is short stroking.

 

Regardless of why the bolt doesn't lock back, this should tell you IF the bolt is getting there to begin with.

 

My $.02 worth

Link to comment
Share on other sites

Hey thanks everybody for the help,

giantpanda4 that is a good quest. no the bolt

does not stay back after last shot, it is down agaisnt

the mag. I ain't even though of that. By that, the bolt

can't be going back to lock in the sear noch.

But now why ain't it going back. My ammo is plenty

hot, trying it will miltary ball. 230gr FMJ ball.

Bolt moves fine by hand and is not binding will

recoil spring.

There is some rub marks in ejector grove on the bolt,

think that might be enough to slow bolt down.

The h-peice seams to be moveing slick.

 

Question: If I take a wood dowel and run down the

barrel and push against the bolt face to act as a round

is being fired, how much pressure does it take to force

the bolt back out of battery?

 

Oh and Motorcar if I can't fix this and give up I will

start the bidding at $5000.00. LOL

Or still may stick a tomato plant with it.

Norm I will try that tape thing tommorrow just to

double check it. Good ideal.

Again thanks all

BA

http://www.machinegunbooks.com/forums/invboard1_1_2/upload/html/emoticons/rolleyes.gif

Link to comment
Share on other sites

Put a wooden dowel down the barrel against the bolt face and stand the gun on the end of the dowel on a bathroom scale, push on the butt- it usually takes about 40# to disengage the lock (don’t count the weight of the gun).

 

Clean the top of the receiver with degreaser and use masking tape to determine the travel of the bolt.

 

You have received very good direction concerning many possibilities that could be causing this. Something apparently has changed in the bolt, actuator, lock, receiver relationship and I am concerned about the possibility of metal being moved through battering over time.

 

Insure that there is nothing in the recoil spring hole in the actuator (such as a piece of broken spring).

 

If none of the suggestions offered throughout this thread produces a cure, I suggest you have it inspected.

 

Link to comment
Share on other sites

I shot some Winchester White Box Wal-Mart special in my 28 with varying results. The ammo works fine for the most part, but occasionally I get a round that won't cycle the gun fully. When you let off the trigger, it only cocks to the second notch.

 

IMI is hotter and consistent. I also have some Spanish and FN ball ammo from WWII that I haven't tried yet.

 

 

Have you manually checked (cycled) the gun yet??? Cock the gun open, hold the actuator knob, and squeeze the trigger. Holding the trigger down, let the bolt go fuly home (not slam down) then re-cock with the trigger still held down. Go through several cycles, then start the bolt back and about half way through the cycle, let off the trigger and see what happens. I'm curious to see whether letting off the trigger will stop the bolt from cycling and let the gun re-cock.

 

Not the same as with live ammo, but it might give you a hint of something.

 

Good luck. These guys are better at this than I am, but that is my contribution.

 

Ken

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

×
×
  • Create New...