Homealone1 Posted October 14, 2020 Report Share Posted October 14, 2020 I have a York MK2 sten gun. It feeds and ejects great but after the last round the stock will pop off. When dry firing the return spring housing jumps forward when the bolt hits the trunnion allowing the stock to come off if there is any downward pressure being applied to the stock. Ive tried replacing the recoil spring with 2 others and also swapped recoil spring housings with one from a known good Sten MK5. Ive also tried replacing the bolt with a steel bolt instead of the brass one. Nothing seems to be binding, Im at a loss as far as what is going on. Link to comment Share on other sites More sharing options...
Homealone1 Posted October 14, 2020 Author Report Share Posted October 14, 2020 So , know there is at least 1 other person having this issue. I had the day off today and decided to tinker with it. The button on the return housing was super easy to push in and my stock was a little loose. I took a piece of paper and folded it to the thickness of the a lot that accepts the stock and removed layer by layer until the stock would just barely snap into place. The stock still is loose on the bottom but has no vertical play anymore. Now the button is just a little sticky when pressing it in. Ill have to measure the round portion on a few Sten stocks to find one with a larger diameter. Ill add photos below Link to comment Share on other sites More sharing options...
Homealone1 Posted October 14, 2020 Author Report Share Posted October 14, 2020 (edited) Here is the fix Edited October 14, 2020 by Homealone1 Link to comment Share on other sites More sharing options...
Robert Henley Posted October 14, 2020 Report Share Posted October 14, 2020 My MK II loop stock was too tight, and I had to use a rubber mallet and tap it off. I bought a MK V (wooden) stock, and it fits perfectly. I understand there is a lot of variance in specs, For example, have to try different magazines to get some that fit the magazine well. Perhaps try a different stock. 1 Link to comment Share on other sites More sharing options...
Homealone1 Posted October 14, 2020 Author Report Share Posted October 14, 2020 That is the plan , but for now at least it is functional. I’ll have to try a few stocks and see what works, loop stocks are 65 bucks and up now so I don’t want to just order a bunch and be stuck with them. Link to comment Share on other sites More sharing options...
huggytree Posted October 14, 2020 Report Share Posted October 14, 2020 Howd you like to be in ww2 and be issued that sten Shooting Germans and your gun falls apart! Link to comment Share on other sites More sharing options...
Homealone1 Posted October 14, 2020 Author Report Share Posted October 14, 2020 Howd you like to be in ww2 and be issued that sten Shooting Germans and your gun falls apart!I’d just be happy it reliably feed and ejects lol Link to comment Share on other sites More sharing options...
Annihilator Posted October 15, 2020 Report Share Posted October 15, 2020 It failed with Heydrich,,, Link to comment Share on other sites More sharing options...
APEXgunparts Posted October 15, 2020 Report Share Posted October 15, 2020 It failed with Heydrich,,, Because the resistance fighter tried to fire the STEN with the stock removed.The spring cap came out of the tube with the first shot and the gun was useless after that.A mistake that cost them their lives. Richard Link to comment Share on other sites More sharing options...
johnsonlmg41 Posted October 16, 2020 Report Share Posted October 16, 2020 Is the spring attached to the cap? Is the cap rotated into the locking position? Are tabs broken off the cap? The gun can be fired without the stock, I just don't know what you'd hang on to though? The Sten guns function very well or the Germans wouldn't have bothered making them. Of course on the other hand the British Sten is a copy of earlier German guns that all functioned very well. Link to comment Share on other sites More sharing options...
APEXgunparts Posted October 16, 2020 Report Share Posted October 16, 2020 On mine the spring is very tight in the "spring return housing", the "spring return cap" presses in and turns easily.Removing the stock seems simple enough, not a lot of pressure to push the "spring return housing" back thru the locating hole in the stock.The British Para's actually had a blanking plate to fit into the back of the STEN so it could be fired with the stock dismounted.It is carrier in the in a compartment on the Airborne bayonet frog.https://www.sofmilitary.co.uk/sten-gun-blanking-plate.htmlRichard 1 Link to comment Share on other sites More sharing options...
johnsonlmg41 Posted October 18, 2020 Report Share Posted October 18, 2020 Richard, that is a cool piece! Designed for the MK5 though.....since you have two grips to hold onto. I recalled seeing it in Seagul's book when you posted the picture and had forgotten about it. I'm guessing finding one of those will be a project? To the OP, swapping out to a MK5 setup may be risky. Bolts are different and old springs may have additional compression due to the shorter stroke/ distance. Best to swap out working MKII parts. Link to comment Share on other sites More sharing options...
Waldo Posted October 18, 2020 Report Share Posted October 18, 2020 I have a Mark II Sten that was bought back from Korea and registered during the 1968 Amnesty. It sat in an attic for many years. I do not know if it was ever shot in this country. I bought it about 1984. It is pretty beat up. It came with a T-stock. I needed some parts and purchased a parts kit. I think from Sarco. The parts kit came with a loop stock. I have fired the gun with both stocks. The loop stock always falls off, some times in the middle of a burst. I have never had that happen with the T-stock. The dimension from the center hole of the loop stock is noticeably longer than the T-stock. I have looked at other Stens with both kinds of stocks. I think there is a variation in the size of the part of the stock that attaches to the gun, depending on where and when the stock was made. I think that it is more noticeable with the loop stocks than the T-stocks. I think you should check the dimension on your stock and then see if you can find someone selling stocks and get them to measure a few for you. Link to comment Share on other sites More sharing options...
Barry Posted October 19, 2020 Report Share Posted October 19, 2020 (edited) I thought the end spring cap locked in hole on the stockIf spring has lost strength then I could see lack of pressure on end cap could let it move forward allowing the stock to move down and possibly offSee how much resistance is on the cap when you push it by hand Edited October 19, 2020 by Barry Link to comment Share on other sites More sharing options...
Bret_T Posted October 21, 2020 Report Share Posted October 21, 2020 My Sten is having the same problem with the stock sliding off. It seems that the recoil allows the cap to go in just enough to release the stock. Note that my stock is not original to the Sten. The original owner lost it somehow. I'm definitely open to replacing it, but would prefer the loop type. Meanwhile, I'll give Homealone1's fix a try. Link to comment Share on other sites More sharing options...
2ndArmored Posted October 22, 2020 Report Share Posted October 22, 2020 If you don't have a range timer to verify it, go online and note the cycle rates of other Stens being fired. If yours is noticeably slower, then it would be additional evidence that your recoil spring (return spring) is damaged/too weak/too short. Link to comment Share on other sites More sharing options...
Bret_T Posted October 22, 2020 Report Share Posted October 22, 2020 I already replaced my recoil spring with a new one. It might have helped some, but didn't solve the problem. Link to comment Share on other sites More sharing options...
johnsonlmg41 Posted October 23, 2020 Report Share Posted October 23, 2020 Bad springs, the plunger/cap should never move forward. RTG has NEW springs in stock. I mean new, not surplus used, but new to you. Take your spring out and measure it. It should be at least 9.5" at the least. The rear cap lugs have to be in the slot and rotated to the locked position. HTH Link to comment Share on other sites More sharing options...
Bret_T Posted October 23, 2020 Report Share Posted October 23, 2020 My new recoil spring measures right at 9". I bought it from Northridge and it definitely appeared new. I just ordered the spring set from RTG Parts and will let y'all know if it solves the problem. Link to comment Share on other sites More sharing options...
huggytree Posted October 23, 2020 Report Share Posted October 23, 2020 Could the slot the cup locks into be loose/ worn ? Or out of spec. ? Maybe try a new cup and see it it fits tighter I have to push hard to get my cup into the tube. Its so tight I have to use a pliers to twist it out Link to comment Share on other sites More sharing options...
Bret_T Posted November 2, 2020 Report Share Posted November 2, 2020 I received the spring set from RTG Parts. The recoil spring is obviously stiffer and is a full 1.5" longer than the one that I received from Northridge. The other springs I received also appear to be new. I installed the RTG recoil spring and went shooting. I started with Remington UMC 115gr FMJ in semiauto mode. The rifle would shoot bursts of about 3 to 7 shots. I was thinking, what's going on? Perhaps I put the selector on auto, so I slid it over. It would shoot, but would continue shooting a few shots after I let off the trigger. Then it dawned on me. The low powered Remington UMC ammo coupled with the new spring was powerful enough to eject and feed, but not powerful enough to push the bolt back to where it would catch. I then tried some Magtech 115gr FMJ and it ran fine. I'm definitely pleased with the RTG Parts spring set and really appreciate the recommendation. I'll just have to remember not to shoot low power 9mm through the Sten. Link to comment Share on other sites More sharing options...
johnsonlmg41 Posted November 4, 2020 Report Share Posted November 4, 2020 It's likely your new spring will take a set and the lower powered ammo will work fine at some point. The other option would be to clip a coil, but I think in time it will wear in. You could leave it cocked for a period of time as well? I assume the stock stays on while shooting as well? Low power ammo is a problem for a lot of open bolt guns when the sear doesn't catch. It's a delicate balancing act between ammo, spring tension, catching the sear, and not beating the end of the receiver. Link to comment Share on other sites More sharing options...
Bret_T Posted November 4, 2020 Report Share Posted November 4, 2020 I'm not worried about it. I have plenty of other 9mm that will work just fine. I'm very happy with the performance right now. Hopefully the stock will stay put. Link to comment Share on other sites More sharing options...
Homealone1 Posted November 6, 2020 Author Report Share Posted November 6, 2020 Ill have to order a set of those springs. My fix works for me but it sure is janky. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now