Tiz Posted February 20 Author Report Share Posted February 20 31 minutes ago, JWB said: TIZ, If you have any Mag Lip tools, I would like one, or please put me on the list for when you have them again. Thank You. You are on the list for the next run of mag tools. Tiz Link to comment Share on other sites More sharing options...
Doug Quaid Posted February 20 Report Share Posted February 20 I don't want to micturate into Tiz's rice crispies or anything, but I was very pleased with the feed lip tool that I got from Deerslayer. It's basically two pieces of curved metal that are welded to a vice grips I fixed a couple of majorly crushed up magazines with it and they came out like brand new. So that is an option, FYI. Link to comment Share on other sites More sharing options...
Tiz Posted February 21 Author Report Share Posted February 21 No worries Doug. There are several way to skin a cat as they say. Sorry i did not have any mag tools in inventory when you first contacted me. I have been able to do a small run since. I assume I can take your name off the back order list. All the best brother. Tiz Link to comment Share on other sites More sharing options...
Doug Quaid Posted February 21 Report Share Posted February 21 I did not know you were making them again. You may take me off your back order list, thanks. I'm curious what your gizmo looks like. Is it a form that goes up inside the mag? The deerslayer tool is a pair of pliers that has a jaw that is shaped identically to the normal feed lip contour, you position the tool appropriately and squeeze and the giant camming power of the vice grips does the rest. Link to comment Share on other sites More sharing options...
Tiz Posted February 21 Author Report Share Posted February 21 Doug, At the time you asked about one I had none, but as they say, due to popular demand, I made a few more. Anyway send me a PM with your email and I will send you some picture of the mag tool. Best Tiz Link to comment Share on other sites More sharing options...
Rekraps Posted March 13 Report Share Posted March 13 Hey everyone, Tiz asked me to post my experience with the magazine lip repair/realignment tool. So I ordered one and it arrive nicely wrapped in bubble wrap, with a full page of detailed instructions. I have 10 OEM 30 rounders and six OEM 20 rounders that I use in my AO 1928 A1. I found the quality of the tool to be wonderful, talk about a strong unit. Solid steel with two "bullet" lip aligners at the top and an alignment port (threaded hole) that matches the magazine lock hole. The way it is supposed to work is that once the mag is disassembled, the tool is inserted and secured with the bolt which fits through the magazine lock hole. Once secured, a nylon or rubber mallet/hammer is used to reform the feed lips around the "bullets" at the top of the tool. Reaming out the magazine lock hole (there is some internal metal that has to be filed away in order for the bolt to slide through) was the most time consuming. I had to use a long round file, securing the magazine in a vice and carefully removing the internal metal until the bolt easily slipped in. The issue I ran into is interesting. Not a single magazine I owned, when the tool was inserted, aligned with the alignment hole. Really? The tool had to be out of spec right? Wrong. The alignment tool is 100% perfect. It was the magazine lips that were out of spec. One would think that they would bend upward, but in my case all of them were bent slightly inward, thus not allowing the tool to be aligned with the bolt. So, holding each magazine upside down, I inserted the tool and used a big hammer to pound the stuffing out of it until the alignment hole came into perfect position. Then, I inserted the bolt/washer, flipped the magazine around and used the nylon/rubber hammer to make sure the feed lips were flat against the "bullets". Then I tested each magazine to make sure it would load into the gun. Perfect. The most common issue I saw was that the forward (front) part of the lips tended to be bent in slightly (probably from rough handling) and even a little bend puts the magazine out of spec. Would they work? Yes, but it was not in spec. Once I was finished (1.5 hours for all the mags) they all looked perfect. My hat is off to Tiz for taking the time to design this tool. If you are having issues with the alignment hole matching the magazine lock hole, its the magazine, not the tool. Get a bigger hammer! Thanks Tiz! Link to comment Share on other sites More sharing options...
Tiz Posted March 13 Author Report Share Posted March 13 31 minutes ago, Rekraps said: Hey everyone, Tiz asked me to post my experience with the magazine lip repair/realignment tool. So I ordered one and it arrive nicely wrapped in bubble wrap, with a full page of detailed instructions. I have 10 OEM 30 rounders and six OEM 20 rounders that I use in my AO 1928 A1. I found the quality of the tool to be wonderful, talk about a strong unit. Solid steel with two "bullet" lip aligners at the top and an alignment port (threaded hole) that matches the magazine lock hole. The way it is supposed to work is that once the mag is disassembled, the tool is inserted and secured with the bolt which fits through the magazine lock hole. Once secured, a nylon or rubber mallet/hammer is used to reform the feed lips around the "bullets" at the top of the tool. Reaming out the magazine lock hole (there is some internal metal that has to be filed away in order for the bolt to slide through) was the most time consuming. I had to use a long round file, securing the magazine in a vice and carefully removing the internal metal until the bolt easily slipped in. The issue I ran into is interesting. Not a single magazine I owned, when the tool was inserted, aligned with the alignment hole. Really? The tool had to be out of spec right? Wrong. The alignment tool is 100% perfect. It was the magazine lips that were out of spec. One would think that they would bend upward, but in my case all of them were bent slightly inward, thus not allowing the tool to be aligned with the bolt. So, holding each magazine upside down, I inserted the tool and used a big hammer to pound the stuffing out of it until the alignment hole came into perfect position. Then, I inserted the bolt/washer, flipped the magazine around and used the nylon/rubber hammer to make sure the feed lips were flat against the "bullets". Then I tested each magazine to make sure it would load into the gun. Perfect. The most common issue I saw was that the forward (front) part of the lips tended to be bent in slightly (probably from rough handling) and even a little bend puts the magazine out of spec. Would they work? Yes, but it was not in spec. Once I was finished (1.5 hours for all the mags) they all looked perfect. My hat is off to Tiz for taking the time to design this tool. If you are having issues with the alignment hole matching the magazine lock hole, its the magazine, not the tool. Get a bigger hammer! Thanks Tiz! Recaps, Thanks for posting your experience. Tiz Link to comment Share on other sites More sharing options...
BEATNGU Posted September 11 Report Share Posted September 11 First post on this forum cause I've been searching high and low for this type of tool. So don't mind the user name, came to mind after recently watching jeepers creepers. Tiz, would you happen to have any of these tools for sale at the moment? Link to comment Share on other sites More sharing options...
Stampcollector Posted September 11 Report Share Posted September 11 I would like one also if they are for sale! Link to comment Share on other sites More sharing options...
Rekraps Posted September 12 Report Share Posted September 12 This tool is a great investment.. I wish we had one for the MP40 mags and PPSH mags. Link to comment Share on other sites More sharing options...
Tiz Posted September 12 Author Report Share Posted September 12 23 hours ago, BEATNGU said: First post on this forum cause I've been searching high and low for this type of tool. So don't mind the user name, came to mind after recently watching jeepers creepers. Tiz, would you happen to have any of these tools for sale at the moment? At the present time I do not have any tools available and haven't made any for a few months. Looks like I may have to do another small run if some of "yinz guys"( a PA thing ) are really interested. I thought that I had pretty much addressed the needs of the community, maybe not. Link to comment Share on other sites More sharing options...
BEATNGU Posted September 12 Report Share Posted September 12 8 hours ago, Tiz said: At the present time I do not have any tools available and haven't made any for a few months. Looks like I may have to do another small run if some of "yinz guys"( a PA thing ) are really interested. I thought that I had pretty much addressed the needs of the community, maybe not. My part of the state, everyone gets called "bott" or "bud" lol. If you do decide to make a couple more, I'd definitely like to have one. Probably be good to have one on hand. Seeing as the mags I have, probably all need tweaked a bit here or there. Thanks for the reply Tiz. Link to comment Share on other sites More sharing options...
pstidan Posted September 12 Report Share Posted September 12 9 hours ago, Tiz said: ... "yinz guys"( a PA thing ) ... For the record, "yinz guys" is a western PA thing while "youz guys" is an eastern PA thing. Just saying... Link to comment Share on other sites More sharing options...
Tiz Posted September 13 Author Report Share Posted September 13 (edited) You are correct I just happen to live on the "yinz" side of PA. How would a Texan have such in depth knowledge of PA slang? Thanks Tiz Edited September 13 by Tiz Link to comment Share on other sites More sharing options...
Flyeagle58 Posted September 13 Report Share Posted September 13 Tiz, I would also like to get one if you decide to make some more! Link to comment Share on other sites More sharing options...
Tiz Posted September 13 Author Report Share Posted September 13 Beatngu & Flyeagle, I have placed you on the interested list. Stand by. Best Tiz. Link to comment Share on other sites More sharing options...
pstidan Posted September 13 Report Share Posted September 13 1 hour ago, Tiz said: You are correct I just happen to live on the "yinz" side of PA. How would a Texan have such in depth knowledge of PA slang? Thanks Tiz I grew up in the "youz" side of PA, went to school in the "yinz" side of PA, got tired of the winters in both sides of PA, and moved to CA. A few years later I was transferred to Austin and decided to hang around. Link to comment Share on other sites More sharing options...
Tiz Posted September 13 Author Report Share Posted September 13 (edited) 54 minutes ago, pstidan said: I grew up in the "youz" side of PA, went to school in the "yinz" side of PA, got tired of the winters in both sides of PA, and moved to CA. A few years later I was transferred to Austin and decided to hang around. As Ricky Ricardo would say "that splans everything" I have always said that since I never had the good sense to move out of this part of the country I try not to complain. Edited September 13 by Tiz Link to comment Share on other sites More sharing options...
jonnyjon88 Posted September 15 Report Share Posted September 15 I will take one too please Link to comment Share on other sites More sharing options...
Tiz Posted September 16 Author Report Share Posted September 16 I have added you to the wait list. Thanks Tiz Link to comment Share on other sites More sharing options...
ColdWarShot Posted September 25 Report Share Posted September 25 I’m interested in a Feedlip tool as well! Link to comment Share on other sites More sharing options...
Tiz Posted September 25 Author Report Share Posted September 25 OK. Looks as if I best get busy. You are on the list ColdWarShot Link to comment Share on other sites More sharing options...
pvt81pvi Posted September 25 Report Share Posted September 25 Any possibility adding me to the list for a tool? Link to comment Share on other sites More sharing options...
Tiz Posted September 25 Author Report Share Posted September 25 You are on the list as well. Thanks Link to comment Share on other sites More sharing options...
Lawman9328 Posted Tuesday at 12:18 AM Report Share Posted Tuesday at 12:18 AM Please add me as well.....Thanks Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now