Jump to content

Parts For Replica Thompson


Recommended Posts

Just got a hold of an all-metal replica M-1921 Thompson, minus the buttstock; does anyone know where I can get a hold of a buttstock & horizontal foregrip ( it has a vertical on it now) or if actual parts can fit on this? The receiver appears to be slotted for a buttstock, and it has a 50rd drum w/ it. A 30rd magazine will not properly fit into the magazine well either (mag needs to be filed down on the sides I think)

 

I'm a Plt Sgt for the 81mm Mortar Plt of 2/505 PIR in the 82D ABN DIV at Fort Bragg & just got into collecting & doing Living History w/ the 82D AB Museum

 

Thanks

 

H-MINUS!

 

Chris Lewis

Link to comment
Share on other sites

I'm pretty sure a real '21 buttstock with slide hardware will fit, if the replica is an MGC (Modelgun Corp., Japan). The dimensions on those guns were very, very close to the original. But alas, a regular 30-round mag doesn't like to fit well. Nice that you got the drum with it! Horizontal foregrip from Sarco, IMA, forum members here, etc., will fit fine. They have buttstocks from time to time too.

 

Welcome aboard!

Link to comment
Share on other sites

lewis505,

 

Look up "deerslayer" in the member list and email him. He can make the stock for you and stain all of your wood to match.

 

Norm

Link to comment
Share on other sites

I just checked my MGC gun and slide (oops butt stock attachment assembly) and compared it to a tommygun slide and a numrich frame.

 

Results.

A tommygun slide will not slide into place on my MGC gun. Checking things quickly with a caliper, you would need to remove .05 inches from the MGC frame to get it to fit. That would probably take about 2 minutes with a sanding block and sandpaper.

 

I could, just barely, get the MGC slide onto my numrich frame.

 

I don't have time right now to post a picture of all of this but the MGC frame was just a little bigger across the bottom than the channel in the slide.

 

Hope this helps.

Dan

 

Link to comment
Share on other sites

In my earlier, more ignorant days, I tried to modify a nice 28 buttstock to fit the MGC hardware. After carving the wood, I soon discovered that it was very difficult for me to make the fit. I had a terrible mess.
Link to comment
Share on other sites

Hmmm,

 

I could easily fit the slide to the MGC without modifying your "gun" at no extra charge. Best if I had the frame in hand though. http://www.machinegunbooks.com/forums/invboard1_1_2/upload/html/emoticons/rolleyes.gif

 

Damon

 

Link to comment
Share on other sites

lewis505,

 

TommyGunner can fit a stock slide assembly very well to your MGC frame if you send it to him. I have a Numrich 28 frame that was "odd size" and a normal slide assembly would not fit. After sending the frame and slide to Tommygunner; it fit perfectly.

 

He does good work and has a fast turn around on work.

 

Have you ever considered going to a functioning 1927? They are just as nice to look at, and you can shoot it too. With the help of some fellow members of this board, you can have a VERY nice, functioning gun. For $200 and ATF aproval, you can have one that looks just like a 1921 and functions (except no full auto.)

 

If you want to see a 1927 at it's best, follow this link to the old board. It belongs to Lionhart (lucky b@$t@rd!). http://www.machinegunbooks.com/forums/invboard1_1_2/upload/html/emoticons/wink.gif You too, could have a gun like this. Look through the complete post as the best pictures are in the middle. In case you didn't notice, it is the gun at the top of THIS webpage!

 

http://www.machinegunbooks.com/cgibin/ikon...um=1&topic=2109

 

Norm

 

 

Link to comment
Share on other sites

QUOTE (TommyGunner @ Sep 22 2003, 11:54 AM)
Hmmm,

I could easily fit the slide to the MGC without modifying your "gun" at no extra charge. Best if I had the frame in hand though. http://www.machinegunbooks.com/forums/invboard1_1_2/upload/html/emoticons/rolleyes.gif

Damon

could easily fit the slide to the MGC without modifying your "gun" at no extra charge. Best if I had the frame in hand though. http://www.machinegunbooks.com/forums/invboard1_1_2/upload/html/emoticons/rolleyes.gif

 

Cool - might be some 82d Goodies in it for you!

When I get some more "loose" $$$ I'll get my hands on a stock & contact you

 

AIRBORNE!

 

Chris

Link to comment
Share on other sites

Chris,

 

Well it seems that you have found my weakness! I am a sucker for those goodies! http://www.machinegunbooks.com/forums/invboard1_1_2/upload/html/emoticons/biggrin.gif If I may make a suggestion. IMHO it would work out best if the stockmaker had the slide when finishing the stock. For example: if deerslayer was to make a stock for you...I would send him the slide...He would then fit and sand the stock right up to the slide making a perfect fit this way (it is harder to fit a slide into an existing stock...but not impossible). The slide would then be returned to me (hopefully with your frame for fitting) and I would bead blast the slide and reblue. This would ensure the best fit and would save the vintage 21 wood (which is getting very hard to find and expensive) for a full auto. At any rate...I beleive that it would be best for the person fitting the stock to have the slide in hand...and of course I recommend Deerslayer. We will work together on it to ensure the best. He put together a AAA fancy stockset for a customer of mine and It is so beautiful I don't want to give it up! Not to mention it is cheaper than a vintage 21 Stock (no crossbolt). I will try to get some good pics of his work up tonite for you to look over. Let me know if you have any questions.

 

Damon

Link to comment
Share on other sites

Lionhart--

Everytime I see your project, I am astonished! I'm still saving up to have the PK magic done to mine.

Link to comment
Share on other sites

Here are the pics of that beautiful AAA fancy stockset Deerslayer made. I know it doesn't fit in the scheme of the vintage wood but I think it is very nice none the less and the workmanship was very high quality in my opinion. The peices were very symetrical and even. Looked more machined than hand made.

 

http://www.tommygunner.com/images/aaastock/buttstock.jpg

 

http://www.tommygunner.com/images/aaastock/foregrip.jpg

 

http://www.tommygunner.com/images/aaastock/reargrip.jpg

 

Thought you might like to see these. I can't stop playing with them! I am about to hook up my 27 and will have Deerslayer make my wood for sure. http://www.machinegunbooks.com/forums/invboard1_1_2/upload/html/emoticons/biggrin.gif

 

BTW...PK and Devlin set the bar with Project X. I have given much thought and haven't come up with a substantial improvement yet! Great guns!

 

Damon

Link to comment
Share on other sites

Ok...here are the pics of Chris's model gun. I think it is interesting with the park finish. I have seen swivels on the foregrip like that on a couple of the commemorative thompsons from west hurley. This is a new one by me...anyone have any info on this?

 

http://www.tommygunner.com/images/chrisreplica/Kokusai1.jpg

 

http://www.tommygunner.com/images/chrisreplica/Kokusai2.jpg

 

http://www.tommygunner.com/images/chrisreplica/Kokusai3.jpg

 

Enjoy,

 

Damon http://www.machinegunbooks.com/forums/invboard1_1_2/upload/html/emoticons/biggrin.gif

Link to comment
Share on other sites

Chris, I noticed the markings on the reciever are different than the typical MGC gun. Does this one take the plug fire "rounds"? What does your chamber look like?

 

MGC made two types of plug fires. One used a hollow "round" with a simple paper cap pushed inside. The chamber had a hollow post that would strike the cap when the round chambered. This was the older type.

 

The newer one used a plastic cap somewhat similar looking to a typical muzzle loader cap. The chamber had a solid post. The plug fire round is the same size as a .45 acp. The top and bottom part screw together and inside a cap can be placed to make the thing work. The solid post hit the internal parts of the round to make the cap explode and thus power the ejection. The rounds usually sell for at least $5 when you can find them.

Dan

Link to comment
Share on other sites

That is an interesting gun. Never heard of that company. And Dan, thanks for the explanation on the plug fire subject. I didn't know how that worked.

 

By the way: There's a guy a Ebay who sells a "firing pin" for MGC Thompsons that aren't factory-equipped for the plug fire. How can that work??? He wants like $75 for it, and I didn't go for it. Any ideas?

 

Thanks,

 

Ron

Link to comment
Share on other sites

Ron, actually, MGC made 4 types of cartridges (1. the brass paper cap cartridge (2. plastic paper cap cartridge (3. the "CP" type (4. the HW type (improved piston sealing) The "Plug Cap firing" system was invented by Marushin.

 

 

the "firing pin" is actually a "chamber" with a firing pin in it, facing the cartridge. of course this firing pin enters the "hollow point" in the the round and hits the "CP" (Cap Piston) which is forced backwards (this piston usually has a O-ring as in the case of the later versions of the cartridges or an old fired cap, that acts as a gas seal) now, this piston has a projection which hits the cap that is facing powder side up at the cartridge bottom. This of course, ignites the cap.The gasses then impinge on the piston and seal and force the piston against the firing pin this supplies the power to blow-back the action.

 

 

 

This chamber of course is made to replace either the "paper cap" cartridge chamber/firing pin, or the dummy (solid!) chamber that the "collectors armory" chose to insert into some (but not all) of these modelguns. As for the Kokusai company, they made lot's of modelguns over the years, nice ones too.

Link to comment
Share on other sites

The ebay "firing pins" are being made by a guy I've delt with. Seems like some guns were "demilitartized" by cutting the bolt at an angle and taking out the "firing pin" and replacing it with a solid plug. I've had three of them like that. Makes me wonder why someone (collectors armory???) would go to the trouble to delimitarize a toy gun? Maybe it went to Europe at some point in its life. Anyway, I made a new plug and was visiting with the ebay seller (his name is Roger by the way) about it and so he got the idea to have a bunch of them made up at a machine shop. They are very nicely made.

Now the only problem if you have one of the butchered guns to to fix the bolt. I've had some success doing that. The other problem is getting the solid plug out. They are usually stuck in there with a roll pin that doesn't want to come out.

Dan

 

Link to comment
Share on other sites

Thanks for all the clarification, fellers. Interesting to learn how the different cartridges function. I know that the Collectors Armoury folks were looking to a vendor in Spain for better prices on modelguns, since the $ vs. yen situation was really grim in the early 90's. But my MGC is definitely Land of the Rising Sun. Some pistol models were brought in from Spain.

Any knowledge of a PPSh-41 put out by that Kokusai company? I'm still hunting for one, just static display.

 

Link to comment
Share on other sites

Not sure of what type of "round" my gun shoots as none came w/ it! http://www.machinegunbooks.com/forums/invboard1_1_2/upload/html/emoticons/sad.gif

 

The 50 rd drum is basically empty too - no springs inside of it

 

Thanks for everyone's help w/ this!

 

AIRBORNE!

 

Chris

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

×
×
  • Create New...