Feed Lever Cam

[Cav Trooper]

I need a feed lever cam and have seen them on Gunbroker minus the retainer parts, Numrich has one complete, list as "New Style". Will the new style work with a M60E1 and the original feed parts?

 

Thanks,

 

CT

[MG08]

Was looking to see what part you need, and am not clear from your label - I copied the TM descriptions below. Parts should interchange, but I have not verified the new part No. and old will yet. Can you clarify the part you need ? I may have the part in hand, otherwise I am getting a big pile of NOS M60 parts on Monday. will need to inventory them but it is likely the part will be there.

 

 

GROUP 08:COVER ASSEMBLY

FIG.15 COVER AND LEVER ASSEMBLY
1 PAFFF 19204 11699814 CAM ASSEMBLY,FEED (SEE FIG.16 FOR 1
ASSEMBLY BREAKDOWN)
UOC:G79,023
2 PAFZZ 19204 7269117 GUIDE,CARTRIDGE REAR 1
UOC:G79,023
3 PAFZZ 19204 7269116 GUIDE,CARTRIDGE FRONT 1
UOC:G79,023
4 AFFFF 19204 7269119 LEVER ASSEMBLY,FEED (SEE FIG.16 1
FOR ASSEMBLY BREAKDOWN)
UOC:G79,023
5 PAOZZ 19204 11686315 SPRING,HELICAL 1
UOC:G79,023
6 PAFFF 19204 7269120 PAWL ASSEMBLY,CAM FEED (SEE FIG.17 1
FOR ASSEMBLY BREAKDOWN)
UOC:G79,023
7 PAFZZ 19204 11010152 SHAFT,STRAIGHT 1
UOC:G79,023
8 PAOZZ 96906 MS24665-18 PIN,COTTER 1
UOC:G79,023
9 PAFHH 19204 7269118 HOUSING ASSEMBLY, COVER (SEE FIG. 1
18 FOR ASSEMBLY BREAKDOWN)

 

GROUP 0801: FEED CAM ASSEMBLY

11699814 AND 0802: FEED LEVEL
ASSEMBLY 7269119
FIG. 16 FEED CAM ASSEMBLY AND
FEED LEVER ASSEMBLY
PLUNGER,RETAINER . . . . . . . . . . . . . .
UOC:G79,023
SPRING,HELICAL . . . . . . . . . . . . . . . . . . . . . .
UOC:G79,023
CAM ASSEMBLY, . . . . . . . . . . . . . . . . .
UOC:G79,023
RETAINER,FEED CAM . . . . . . . . . . . . . . . . . . .
UOC:G79,023
..CLIP,SPRING LEVER . . . . . . . . . . . . . . . . .
UOC:G79,023
..LEVER,FEED . . . . . . . . . . . . . . . . . . . . . . . .
UOC:G79,023

[Cav Trooper]

I just got your reply. I have a bid in on the feed lever cam on Gunbroker. Not sure if I'll get it. If not, I will need one. I will also need a few small parts, I've managed to track down most. I do still need a buffer yoke retainer and the shaft for the feed cover. I will look up the pn's.

Where are you located?

 

Thanks,

CT

[MG08]

I got the M60 parts sorted, and inventoried. there were no feed cams but there is a couple NOS front and rear Cartridge guides, and a complete NOS feed pawl assembly. There is also a complete new top cover.( E1 type) ots of other small parts, Bolts, etc. If you want and it is OK with Dave, I can send an XCEL spreadsheet with the parts.

[Cav Trooper]

That would be great, email lgalaske#@gmail.com. take out the # sign.

 

Larry