nfafan Posted September 14, 2004 Report Share Posted September 14, 2004 OK, here's the question please; I have one of the original A-O 1927A1 deluxe that came with the tack-welded 10rd drum in the box with the 30rd stick mag. I've peeked in the drum wondering what could ever be done to make it a true 50rd'r. Now that the ban is over, is there a way to convert it back to a true 50, or am I stuck with a 20th century souvenier of the Klinton era? Any Drum Doctors out there with some hints for those of us with these 10rd display pieces? TIA! Skip Link to comment Share on other sites More sharing options...
PK. Posted September 14, 2004 Report Share Posted September 14, 2004 Yes, they can be converted. The X drum was an L body and cover with ‘plugs’ welded where the normal spiral guide would have been attached. These ‘plugs’ can be removed and a normal spiral guide installed to make an L drum. Re-blue is required Link to comment Share on other sites More sharing options...
snipershot1944 Posted September 14, 2004 Report Share Posted September 14, 2004 PK Can the restoration work be done for less than the cost of a new drum? Link to comment Share on other sites More sharing options...
PK. Posted September 14, 2004 Report Share Posted September 14, 2004 That’s a good question that I don’t have an answer for yet; a lot would depend on how many X’s you were converting. Let’s see how the group buy works out. Link to comment Share on other sites More sharing options...
nfafan Posted September 16, 2004 Author Report Share Posted September 16, 2004 Thanks for the reply! Link to comment Share on other sites More sharing options...
1928a5 Posted September 26, 2004 Report Share Posted September 26, 2004 Being budget minded can you tell me of anyone who might sell me a set of rails to convert an X to a L drum. I had seen a set sold on ebay a few months ago before the sunset. Thanks. Link to comment Share on other sites More sharing options...
LIONHART Posted September 26, 2004 Report Share Posted September 26, 2004 Contact Deerslayer from the Forum here. I know he was tinkering with "X" Drum Conversions. Link to comment Share on other sites More sharing options...
Grey Crow Posted September 26, 2004 Report Share Posted September 26, 2004 Dan made a ring that fits under the rotor and it allows for 30 or 39 rounds. To go to 50 I think he stated that it need spring work. Now don't quote me but I think he was asking 45 for the ring. Link to comment Share on other sites More sharing options...
deerslayer Posted September 27, 2004 Report Share Posted September 27, 2004 The ring is the easy converstion. I refitted guides to a few old WW2 rust bucket drums in the past. 50 rounds requires several hours of fitting new shell guides ($80 worth of time), plus several hours of making them (I've made them for others for $45 in a roughed out state). Then to top of off, the x drum spring isn't strong enough to push out fifty rounds. So you have to pay somebody like Merle to put a new spring in the rotor ($200 more). I'm not looking to do any more of them right now, but if you MUST have it done, I'd do the guide for the above prices. The ring is easy, the spring is strong enough for 30 rounds and I'm making the rings for $45. Got a few orders right now, I'll make a little production run in a couple weeks. Dan Link to comment Share on other sites More sharing options...
Abwehr Posted September 27, 2004 Report Share Posted September 27, 2004 I don't post much on the Forum, but I read it daily. I contacted Dan Block about his conversion of the "X" Drum to a 30 rounder. This sounds like the most cost effective way to convert the "X" Drum. I sent my Drum to Dan last week and he will complete the entire conversion for me. The Ring is $45, the fitting is $20, and the return shipping is $10. I payed $110 for the Drum year before last and another $75 puts me with $185 in it, and that is better than buying the overpriced "L" Drum from Kahr. 30 rounds will work for me since min Thompson is semi anyway. Dan said it would take about 3-4 weeks to get it back and that is fine with me. The Thread was posted on 15 September and here is the address: http://www.machinegunbooks.com/forums/invb...t=ST&f=3&t=3216 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now