billie32 Posted May 2, 2007 Report Share Posted May 2, 2007 what exactly is the registerable part on these guns? I understand that if the receiver is marked M2, then that's that, but what of all the converted M1 carbines? granted, an M1 carbine receiver is an FFL item, but what part of all those m2 bits floating around out there is the real no-no? Link to comment Share on other sites More sharing options...
texasvwnut Posted May 3, 2007 Report Share Posted May 3, 2007 I'm not an M2 carbine expert, however I've seen conversions where the disconnector lever was the registered part. I'm not sure if all are registered this way. Just from my observation. Link to comment Share on other sites More sharing options...
texasvwnut Posted May 8, 2007 Report Share Posted May 8, 2007 I ran into a 'trigger pack' M1 Carbine this weekend. The owner claimed that the serial numbered piece in this gun was the sear, so it may have been up to the person registering, as to what part they wanted to serialize. I'm just guessing here. Link to comment Share on other sites More sharing options...
Ron Mills Posted May 10, 2007 Report Share Posted May 10, 2007 As I recall, it's anything in the group that can convert it, serialed or not. There are a few parts that make 'em go. FullAuto 45 (Mike Hensley) here on the board can give you the full skinny on this one. I used to have the ATF sheet on it, but lost it, like many other things. Better to be safe than http://www.machinegunbooks.com/forums/invboard1_1_2/upload/html/emoticons/nutkick.gif Link to comment Share on other sites More sharing options...
mike in pa Posted May 4, 2008 Report Share Posted May 4, 2008 Mine is the disconnector lever which is the usual part. Other registered parts could be: trigger housing, slide, hammer, disconnector. Link to comment Share on other sites More sharing options...
must Posted May 4, 2008 Report Share Posted May 4, 2008 My M2 carbine is a M1 converted to M2 status. The registered part is the receiver. The form 4 states the receiver serial number of the gun & the classification is a "machine gun". The gun is a Standard Products. Hope this helps. Brent Link to comment Share on other sites More sharing options...
Hnsthart Posted May 20, 2008 Report Share Posted May 20, 2008 (edited) My M2 carbine is a M1 converted to M2 status. The registered part is the receiver. The form 4 states the receiver serial number of the gun & the classification is a "machine gun". The gun is a Standard Products. Hope this helps. Brent I don't have the paper before me at the moment but according to it there are a set parts that even if you don't have a gun to put them in they in and of themselves constitute a machinegun; it takes this group of parts along with an M2 slide, M2 trigger housing, round bolt and stock to make it full-auto. Many M1 Carbines have those parts from an arsenal rebuild or being converted back to M1 from M2 prior to surplusing and they do not present a legality problem. It is when someone has in their possession this group of I think it is 7 parts that are not registered that problems arise. But it takes ALL 7 parts to cross that line--used to be there were quite a few people at gun shows who sold all but one at their tables--which so far as I know didn't create any problems... If this is incorrect info someone please let me know Edited May 20, 2008 by Hnsthart Link to comment Share on other sites More sharing options...
The Lone Ranger Posted June 7, 2008 Report Share Posted June 7, 2008 Info from the NFA Handbook: M2 Carbine conversion kit The above parts consisting of an M2 selector lever, selector lever spring, disconnector lever assembly, M2 disconnector, disconnector spring, disconnector plunger and M2 hammer are classified as a machinegun. These parts are used specifically for fully automatic fire and have no application in a semiautomatic carbine. While other parts such as an M2 sear, operating slide, trigger housing and stock are used in the fully automatic carbine, these parts are also appropriate for use in semiautomatic M1 carbines. Therefore, the M2 sear, operating slide, trigger housing and stock are not a combination of parts designed and intended for use in converting a weapon into a machinegun. As for the marking, the most common one I am familiar with is the disconnector. Unfortunately, I have no idea where to find that in writing. It may well have been in the form of a letter response in years gone by. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now