Weasel

Change the sight over to adjustable. Not hard to due yourself. I installed mine on a 1928a1 get the rivets, make a bucking bar and use a punch on the inside to flair out and then level off good luck

A few years ago the spring in my WW2 L drum stopped working. I talked to the drum doc and he told me there were on springs to be had and to replace with a after market drum spring. I took apart the rotor and it some how had the keeper pop off the end of the spring at the winder center mount. I got it put back on and TIG'ed the cover back together and its running again. I had no idea what made them work until I took it apart and don't no if all the makers are the same style of spring attachment. Never hurts to take a look at the insides. I should have taken some pictures, dang!

An easy way to remove a barrel from a receiver stub, is to weld a large nut onto the stub and use an air wrench on it, they USUALLY spin right off. M1 barrels are general harder to remove because often they have been re-parkerized with the barrel intact. I sold a large stub on GB for $325. Most folks want to keep them. They are hard to come by these days.

Message sent to you.

How much do you want for one? Might work on my A.O. Thompson?? Thanks

I have one of D.R.'s bbl wrench that he made to remove the stub off the parts kits. It has a full wrap around piece and it clears the sight and slides under the forearm mount. I believe the LARGE nut to tighten around the bbl is 1 1/2" and use a impact gun to tighten. I have removed quite a few bbl's from the rec. stub and takes some force to remove. One stub took 5 hits with a 4lb. hammer with a 16" crescent wrench on the stub (striking the wrench handle).t If pictures are needed I can post Weasel

For those of you that have or collect ww2 subgun items for the grease gun, I have for sale a field manual from 30 Oct. 1943. FM 23-41. Condition is very good with 94 pages. Price is $20.00 plus USPS flat rate shipping to your door. PM me if you have interest in the manual. Thanks for looking and Merry Christmas Weasel

Sent Merle an email and have not heard anything back. He may be busy

Hello to all. My ww2 "L" drum seems to have a broken spring. Who does the repair on the drums? Any advise from members would be greatly appreciated. Stay safe

Cool picture of tmg ready for action http://static5.businessinsider.com/image/55d20fcd2acae719008c0be7-1200/seventh-army-men-looking-for-snipers-in-bobenthal-germany.jpg

Weaponsguild is the place to check out the tommys that are built into semi's Weasel

I have two demilled bolts that I will let go for those who have a dummy to use them in. Bottom has an under cut compared to the other picture Don't think it will show. Better than nothing in the ejection port. PM me.

You can do a SBR on a home built semi Thompson from a parts kit. Follow the guide lines so that it can't be made into a FA. Use a after market rec. or weld a cut up receiver. Just make sure the bolt blockers are put in first. Weaponsguild.com has a few designs that work. It can be a lot of work, but the reward is worth it. Isn't going to be cheap to build and you would not want to screw up hard to find parts. Good luck to those who are going to try and build one. Weasel

This is my violin case holding 28a1. real alligator. I use a small piece of leather between drum and receiver.

You don't have to over engineer a simple replacement of the sight. When I built my semi 1928a1 SBR , I used 8p box nails, ground the heads down, cut to a length that would work. I used a piece of 1/4" steel plate for a bucking bar and pinned the inside into the recess in the receiver. They are there to stay. I posted a picture of the job on Weaponsguild. Weasel